Why Your Laundry Habits May Be The Cause Of Your Stinky Washer

Washing machines aren’t supposed to stink! If you have a stinky washer at home, your laundry habits may be the cause. Some simple changes to your routine can help eliminate and prevent the washer mildew that’s making things stink.

Don’t Ignore The Cleaning Cycle!

If you already have a stinky washer, it’s important to first take the necessary steps to remove the offending washer mildew. Most washing machines, especially newer models, have a cleaning cycle built in. The cycle runs without any clothes and uses high water temperatures to kill any mildew and flush out the system.

You can boost the cleaning cycle by adding a washing machine cleaner, such as Smelly Washer. The natural ingredients in Smelly Washer effectively remove odor, fungus and mildew that can cause a stinky washer.

For best results, follow your washing machine manufacturer’s guidelines for running the cleaning cycle. Washing machine cleaners like Smelly Washer should be used about twice a month.

Don’t Let The Clothes Linger!

It happens to the best laundry-doer from time to time. You get busy and forget you had a load of laundry in the washing machine. You come back a few hours later and throw it into the dryer, or you come back the next day and rewash the laundry. But in that little window of time, washer mildew has already started to grow and multiply.

Mildew is a living organism that needs food and a warm, damp environment to grow. The inside of your washing machine when wet clothes are left to linger is the ideal breeding ground for mildew, which makes for a stinky washer.

The best way to combat forgetfulness is to set a reminder. Turning on the “end of cycle signal” on your washer will do the trick if you’re within the vicinity of the laundry room. When you hear it, go put the clothes in the dryer! If you’re going to be moving throughout the house or doing yard work, get a clip on timer.

Don’t Close The Lid Or Door!

The same idea of leaving wet clothes in the washer applies here as well. Even after a cycle is complete, there is still some residual water left in your washer. It can hide under the rim of a top loader and in the rubber door gasket and detergent drawer of a front loader. This remaining water combined with leftover detergent suds or lint can cause washer mildew.

After you’re done doing laundry, don’t be so quick to slam the door or lid. Leave them ajar for a few hours to allow any excess water to evaporate. On a front loader, also pull the detergent drawer out a bit to allow it to dry.

With just a few simple modifications to your laundry habits, you can effectively eliminate and prevent washer mildew, putting an end to your stinky washer problems.

Cleaning Lint From A Stinky Washer

Everyone knows lint collects in a clothes dryer, but few realize that it also collects in washing machines. Dirt and moisture accumulate along with lint, causing washing machine mold and mildew that results in a stinky washer. You can avoid this problem by cleaning the lint traps of your washing machine regularly, which will keep mold and mildew from forming and then spreading throughout your home. This post looks at cleaning these lint traps to remedy or prevent a stinky washer.

Washing Machine Lint Build Up

Just as it does in a dryer, lint builds up in a washer as laundry tumbles. The soap in laundry detergent mixes with the dirt and tumbling action of a wash cycle, which causes lint to form. While a great deal of the dirt and lint rinses out of the tub and down the drain at the end of a wash cycle, some lint splashes above the splash line, sticking to the sides of the tub and attaching to the upper rim of a washer. Lint can also trap in small crevices and on the agitator of the washtub.

Why Cleaning Lint Away Is Important

The collected lint contains dirt and moisture that cause washing machine mold and mildew, leading to a stinky washer. If you clean away the lint, you can avoid the formation of washing machine mold and mildew that will not only contaminate everything you wash, but also spread to other parts of your home.

Cleaning The Lint From Your Stinky Washer

Open your washer and look for lint on the plastic agitator, along the drain hose, and along the top and rim of your machine. Wipe the areas down with a clean, damp cloth, making sure to grab as much lint as possible. Remove the agitator tube from the washer, looking for lint or washing machine mold and mildew along the agitator and filter. Use a damp paper towel or sponge to remove lint attached to the tube while you still have the agitator removed. Peel away any lint on the filter in the agitator tube.

Check the interior rim of your stinky washer for lint. Feel around the rim of the tub, pulling out the lint trap and removing any accumulated lint. Use a damp paper towel or sponge to wipe down the rim to ensure you remove any washing machine mold and mildew. Grab any pieces of lint falling lose when removing the lint trap.

Inspect the drainage hose on your stinky washer for lint. Rinse the drainage hose lint trap with warm water and dry thoroughly before replacing. After cleaning all of the lint traps, double check for any remaining lint and wipe down the interior of the washtub one more time.

By taking the time to clean the filters and lint traps of your washer regularly you will be able to get rid of stinky washer once and for all.

Why You Have A Musty, Stinky Washing Machine

If you have a stinky washing machine, don’t panic. A number of issues can cause a smelly washer. The most important thing is to take care of the mold and mildew that cause the musty smell as soon as possible by cleaning your washer with washer cleaner. If you don’t address the mold and mildew problem immediately with washer cleaner, the musty smell can transfer to your clothing and to other rooms in your home. This post looks at a few of the main reasons you may have a stinky washing machine.

Using Too Much Detergent

By using too much washing detergent, you create an environment favorable for the formation of mold and mildew. Overusing detergent creates more soapsuds and since soapsuds contain air and moisture, they provide the perfect environment for developing a stinky washing machine. If you don’t thoroughly rinse the remaining soapsuds from your washing machine after each load, mold and mildew are likely to form.

An overabundance of soapsuds can also get in the way of your washing machine working properly. Soapsuds can change the tension on the surface of the water. When this surface changes, the soapsuds can work themselves into the sealed bearings inside your stainless steel tub. The moisture that gets into the bearings can ruin them along with ruining your washing machine. It’s expensive to replace these bearings, so it definitely worthwhile to use the correct amount of detergent to avoid a stinky washing machine.

Using Cold Water Only

If you use cold water in your washing machine, you probably don’t know that it keeps detergents from dissolving as well. Hot water is much more effective at dissolving detergent than cold water. When using cold water, detergent particles remain in the tub, even after running it through a complete cycle. These moist, partially dissolved detergent particles provide the optimal home for mold and mildew.

If you do only use cold water, make sure you clean away any detergent particles left behind after each wash and perform a thorough weekly check. In addition, consider running your washing machine through a full hot water cycle at least once per week to dissolve any remaining detergent particles.

Using Fabric Softener

Liquid fabric softener can also provide the ideal breeding ground for mold and mildew. Dispensed during the rinse cycle, liquid fabric softener can collect within the outer part of the tub, causing a stinky washing machine. If fabric softener is necessary, consider dryer sheets instead of liquid fabric softener. Dryer sheets will not provide a place for mold and mildew to grow.

To get rid of the musty odor of mold and mildew due to using too much detergent, only cold water, or liquid fabric softener, use washer cleaner, making sure to follow the directions exactly. A thorough cleaning with washer cleaner can leave any stinky washing machine clean, free of mold and mildew, and smelling fresh.

Reasons Why Your Top Loading Washer Smells

When it comes to getting stinky, top load washing machines can suffer just as much as front load machines. If you have a top load machine with a musty problem, the good news some simple remedies can rid your machine of the stink. Before learning how to clean your smelly washing machine, it’s important to know what is causing your top load to have a problem.

This article looks at several reasons why your top loader has the musty stink of washing machine mold and what you can do to eliminate it so your clothes and home smell clean and fresh again.

Not Using Your Machine Regularly

If you don’t use the washer regularly bacteria and molds have time to grow.  Before you store the unit, leave for a vacation and even if you just don’t use the washer very much your washing habits can keep odor away.

Water temperature is important.  Using mainly cold water for washing is fine, however, a hot wash or soak as your last cycle on wash day will help dissolve residue to flush it out.  It’s a perfect opportunity to do more soiled laundry.  Also, an extra rinse cycle after the last wash will help remove bacteria and residue from the bottom of the tub and drain pump.  This is a great way to prevent having a smelly washing machine.

Overusing Detergent

The amount of detergent used is important when considering the washer odor problem.  With today’s treated water, advanced concentrated detergents and improved washers you really don’t need to use an excessive amount of detergent as achieving the necessary chemical reaction with water only takes a small amount of detergent.  Unless washing very soiled clothing – no more than 1 tbsp of detergent should be used.  This is especially important is using liquid detergent and when washing in treated water.

When overusing detergent too many soapsuds form.  These extra soapsuds can’t all exit the machine during the rinse cycle  and remain in the inside of the unit to become a food source for bacteria and molds.  The splash area just 3-5 inches above the normal water line is the area of heaviest buildup of suds and soiled water that splash up and don’t get rinsed out.

Cleaning Your Top Load Machine

To remove washing machine mold and mildew from your top or front loading washer the procedure of cleaning is as important as what is used.  If you haven’t been able to get rid of odor using baking soda, vinegar or other cleaners Smelly Washer is your answer.  If odor is persistent or returns in laundry add a cap of Smelly Washer or Towel Cleaner to a full load of laundry (preferably whites) and run through a hot setting.  The added bulk of the clothing will raise the washing level to reach the splash area and help remove residue from that area.

For More Extreme Odor

Let the hot water soak the tub for an hour or two to dissolve the built up residue. The longer you soak in hot water and washer cleaner, the better results you’ll have. After a good soaking, turn the machine back on to run the remainder of the cycle.

It’s that easy. The important thing is that you clean your top load machine at the first sign of odor or washing machine mold and mildew. Getting rid of the musty stink of your smelly washing machine will keep your clothes and even your home smelling clean and fresh.

Why You Have A Musty, Stinky Washing Machine

If you have a stinky washing machine, don’t panic. A number of issues can cause a smelly washer. The most important thing is to take care of the mold and mildew that cause the musty smell as soon as possible by cleaning your washer with washer cleaner. If you don’t address the mold and mildew problem immediately with washer cleaner, the musty smell can transfer to your clothing and to other rooms in your home. This post looks at a few of the main reasons you may have a stinky washing machine.

Using Too Much Detergent

By using too much washing detergent, you create an environment favorable for the formation of mold and mildew. Overusing detergent creates more soapsuds and since soapsuds contain air and moisture, they provide the perfect environment for developing a stinky washing machine. If you don’t thoroughly rinse the remaining soapsuds from your washing machine after each load, mold and mildew are likely to form.

An overabundance of soapsuds can also get in the way of your washing machine working properly. Soapsuds can change the tension on the surface of the water. When this surface changes, the soapsuds can work themselves into the sealed bearings inside your stainless steel tub. The moisture that gets into the bearings can ruin them along with ruining your washing machine. It’s expensive to replace these bearings, so it definitely worthwhile to use the correct amount of detergent to avoid a stinky washing machine.

Using Cold Water Only

If you use cold water in your washing machine, you probably don’t know that it keeps detergents from dissolving as well. Hot water is much more effective at dissolving detergent than cold water. When using cold water, detergent residue remains in the tub, even after running it through a complete cycle. These moist, partially dissolved detergent particles provide food for mold and mildew.

If you do only use cold water, make sure you clean away any detergent particles left behind after each wash and perform a thorough weekly check. In addition, consider running your washing machine through a full hot water cycle at least once per week to dissolve any remaining detergent particles.

Using Fabric Softener

Liquid fabric softener can also provide the ideal breeding ground for mold and mildew. Dispensed during the rinse cycle, liquid fabric softener can collect within the outer part of the tub, causing a stinky washing machine.  If fabric softener is necessary, consider dryer sheets instead of liquid fabric softener. Dryer sheets will not provide food for mold and mildew to grow.

To get rid of the musty odor of mold and mildew due to using too much detergent, only cold water, or liquid fabric softener, use washer cleaner, making sure to follow the directions exactly. A thorough cleaning with washer cleaner can leave any stinky washing machine clean, free of mold and mildew, and smelling fresh.

Reasons Why Your Top Load Washer Smells 

When it comes to getting stinky, top load washing machines can suffer just as much as front load machines. If you have a top load machine with a musty problem, the good news some simple remedies can rid your machine of the stink. Before learning how to clean your smelly washing machine, it’s important to know what is causing your top load to have a problem.

This article looks at several reasons why your top loader has the musty stink of washing machine mold and what you can do to eliminate it so your clothes and home smell clean and fresh again.

Not Using Your Machine Regularly

A great way to prevent having a smelly washing machine is to use your top loader regularly. Every time you use your machine, a small amount of water stays behind that does not drain. If you don’t use your machine regularly, that water sits at the bottom of the tub becoming musty washing machine mold and mildew.

By using your top load machine regularly, you prevent that small amount of water left behind from turning into a stinky mess. This is why you should always clean your machine fully if you do not plan to use it regularly.

Overusing Detergent

When using detergent to wash your clothes, you clean the sweat and smells from them. With today’s advanced concentrated detergents, you really don’t need to use an excessive amount of detergent as achieving the necessary chemical reaction with water only takes a small amount of detergent.

When overusing detergent, too many soapsuds form, contributing to the development of washing machine mold and mildew. These extra soapsuds can’t all exit the machine during the rinse cycle and as they remain in the tub, they cause a smelly washing machine by providing food for mold spores to grow.

Cleaning Your Top Load Machine

These instructions are for cleaning a top load machine, not for cleaning a front load washing machine. Ridding a top load machine of washing machine mold presents a special problem because dirty water and soapsuds splash to the top of the outer tub, leaving a residue behind that can cause a smelly washing machine as it forms washing machine mold and mildew.

Begin by running your top load washing machine through its first cycle with hot water and a good washer cleaner. When the tub fills completely with hot water, stop your machine. Fill a couple of buckets with hot water from your sink and add the hot water until you have filled the tub above the splash line.

Let the hot water soak in the tub to dissolve the built up residue. The longer you soak in water and washer cleaner, the better results you’ll have.  Even overnight soaks may be necessary for more extreme cases of washing machine mold. After a good soaking, turn the top load machine back on to run the remainder of the cycle.

It’s that easy. The important thing is that you clean your top load machine at the first sign of odor or washing machine mold and mildew. Getting rid of the musty stink of your smelly washing machine will keep your clothes and your home smelling clean and fresh.

What is the best washer to buy?

With the popularity of 1st and 2nd floor laundry rooms comes a new problem. Because the upper floors are less rigid than lower floors there tend to be vibration problems when a washing machine is used. This vibration can be severe and because sleeping areas are normally upstairs they can be quite disconcerting. The popularity of front loading washers adds to the problem because they spin at twice the speed of the older top loaders. Also, the spin force is horizontal so the floor receives more of that force.

In new homes the problem could be addressed at the early planning states by reinforcing the laundry room floor. Because this adds to the construction costs, most builders and architects are reluctant to do this.

Higher end washers automatically stabilize to reduce vibration. The Bosch washing machine is well known for quiet, dependable models. Also, upper floors water leaks are especially tragic. Their aqua stop systems will stop water from flooding your home.

After the house is built if the bottom of the laundry room floor is accessible the space between the floor joists and directly below the washer can be shored using wood to make the area more rigid. If this is not possible a 4′x4′ cement board or thicker plywood can be placed under the washer to make it stable.

The easiest way for a consumer to address the issue is to make considerations when shopping for a new washing machine.

If the laundry room floor’s rigidity is suspect there are top loading washing machines that now use the same amount or slightly more water than the efficient front loaders. These new washers don’t have transmissions. They use direct drive motors that use magnetism to agitate and spin the tub.

This is not new technology. Domestic manufacturers have “adapted” the direct drive into their units from foreign appliance manufacturers. This is good news for the consumer. These washers have fewer than a dozen moving parts for few repairs. They are quieter because of the lack of a transmission or gearcase. This makes a world of difference for noise suppression.

Note: Many washers tend to have problems with odor. This has has spurred many entrepreneurs creating a large cottage industry of cleaners and other ways to keep odor away.  We created Smelly Washer in 2006 to help with appliance repair.  Tide has their washing machine cleaner and Whirlpool created Affresh to help with alleged design problems in their clothes washers.

Changing washing habits by reducing amount of detergent and softener used and doing a hot wash or soak and even an extra rinse as the last cycle on wash day has shown to drastically reduce odor problems in washers and laundry. Preventive maintenance before residue can accumulate is key to stopping odor transfer to towels and other laundry.

Fabric Softener, Dryer Sheets or Dryer Balls?

To freshen clothing many consumers add liquid fabric softener to their wash.  Softener is dispensed in your washer by either gravity, centrifugal force or by suction created by flowing water and is simply too thick to be properly dispensed.  Because softener is dispensed in the rinse cycle of a washing machine it leaves a residue on the inside of the outer tub.  This residue is a food source for bacteria and mold and the clothes washer can begin to smell bad.

We recommend switching to dryer sheets or even the newer chemical free dryer balls.  Dryer sheets can also be overused. They can be reused and/or cut into halves and still be effective.  The sheets contain chemicals that can coat towels and cause them to be less absorbent. The chemicals can also coat a sensor that detects moisture in clothing on “automatic” settings in almost all dryers. This can cause long dry times and multiple repair attempts.  Do not scrape the sensors to clean.  Use vinegar or rubbing alcohol on a cotton tip to clean them.

Fabric softener and dryer sheets can also clog the dryer lint screen to cause long dry times.  To test your lint screen hold it level and pour a half cup of water on the screen.  If water does not flow easily through the mesh the screen needs cleaning.

If the user is adamant about using softener it should be diluted with water before using. Some experts claim by as much as 6:1 (water to softener, respectively). If used without diluting it can congeal and plug the dispensing ports and/or cause odor.

There are opinions that dryer sheets and fabric softeners contain carcinogens.  The FDA claims that shampoos, detergents, deodorants, creams, soaps and other cosmetic products are not absorbed by the skin.  Many health officials disagree with this stance.   Some links to more expert opinions can be found at http://www.naturalnews.com/002693.html /   http://ezinearticles.com/?The-Toxic-Danger-of-Fabric-Softener-and-Dryer-Sheets&id=16953 /  http://healthychild.org/blog/comments/dinged_by_dryer_sheets/

Dryer balls are a newer, chemical-free alternative to both softeners and sheets. They soften by lifting and separating the clothing which allows air to pass more easily between items. They don’t cause as much noise as one may suspect because of raised nubs which take the force . They aren’t very popular because they don’t leave the fresh scent of softeners and sheets and don’t completely eliminate static cling. The latter is more noticeable in colder climates. The balls cost around ten dollars for a package of two.

Is Rinse Aid Use a Health Issue?

All manufacturers of dishwashers claim that for proper drying rinse aid must be used.  A rinse aid’s only purpose is to aid in drying and reducing waterspots.  It does this by changing the surface tension of water.

When a drop of water is put on a smooth surface it beads up. It is surface tension that holds that bead and it is the natural state of water.  Just a drop of rinse aid changes the surface tension of a lot of water and makes it flow off objects easier.  Rinse aid is dispensed in the rinse cycle and coats the inside of your glass. When a glass from a dishwasher that uses rinse aid is filled with water, bubbles rise to the top and fall back down.  It is not detergent that causes those bubbles – it is rinse aid.

In my opinion, it’s not a good idea for us and especially children to drink anything that changes the surface tension of water.

If you’re not satisfied with how your dishwasher dries without using rinse aid you can pop the door ajar (1″) up to 30 minutes after the “dry” cycle.  This is called “flash” drying and provides venting for moist air to escape from the tub. Do not leave the door open all the way as that is an accident waiting to happen. Also, wood or laminate countertops should have tin tape, poly or varnish applied along the bottom of the countertop just above the dishwasher so moisture doesn’t absorb into the bottom to swell it.  Even if not “flash drying”, this should be done in units venting directly under the countertop .

A few more waterspots may be noticed if no rinse aid is used but one must weigh the practicality of ingesting a chemical against having spotless dishes.

For more opinions:  http://bit.ly/i0DTuc /  Some swear by using white vinegar, See:  http://bit.ly/ewagkl

How to Clean your Dishwasher

Many customers email to ask if Smelly Washer can be used to clean a dish washer. You’d be amazed at how well it works!  If your dishwasher smells, there’s no better way to remove bacteria and mold odor from your dishwasher.

Mold and bacteria can collect deep inside your dishwasher.  Leftover food deposits feed germs that can cause odor and affect the dishwasher cleaning ability.

The best way to clean either a plastic or stainless steel tub dishwasher is to split just a tablespoon of Smelly Washer Cleaner between the dispensers and the floor of the dishwasher.  Start a long, hot cycle such as “pots & pans” or “baked on goods” and allow the cycle to complete.  For more extreme cases, allow the dish washer to soak by popping the door ajar just 1″.  Don’t open the door all the way as it’s easily tripped over and expensive to replace!

If you have food stains (especially from tomato based foods) on plastic bowls or dishes – this procedure may remove those stains if you wash them in the unit with a tbsp of Smelly Washer Cleaner.